GBP (£)
DPA d:dicate™ 4015C Compact Wide Cardioid Mic
This mic is the perfect fill-in between an omnidirectional and a directional microphone.
The off-axis characteristics of this mic are totally linear, a unique quality when it comes to authentic sound reproduction. Any leakage that occurs from off-axis sound sources is still a faithful reproduction of these sounds, just softly attenuated.
Sometimes a conventional cardioid pattern just isn’t quite open enough. Recording orchestras, and other ensembles, sometimes require a compromise between blending in the room reverberation and a more precise localization. When recording instruments with complex radiation patterns, the wide cardioid (also known as hemispheric) design covers a greater sound angle and is an excellent choice. This is the ideal mic for recording grand piano, guitar, marimba and percussion, or as a spot mic for groups in a symphony orchestra. Likewise, it is an excellent speech, dubbing, or vocal mic as its enhanced richness on the bass end nicely compliments many voices.
This is an excellent spot mic as a fill-in between an omni and a cardioid. The compact version is easier to position than other cardioid microphones. Visually discreet, the d:dicate™ 4015C Compact Wide Cardioid Mic represents an indispensably low-profile solution for audio engineers and set designers alike. Tremendously precise and natural sounding, these mics will certainly exceed expectations when used on choirs, percussion setups, grand pianos, wind instruments and much more.
- Low profile – wide pickup area
- Natural reproduction
- Directional ambience pickup
- Exceptional for vocals
- Modular flexibility
| Principle of operation | Pressure gradient | Dynamic range | Typ. 121 dB |
|---|---|---|---|
| Current consumption | 2.8 mA | Polarity | +V at pin 2 for positive sound pressure |
| Directional pattern | Wide cardioid | Total harmonic distortion (THD) | < 1% up to 139 dB SPL peak |
| Power supply (for full performance) | 48 V Phantom power (± 4 V) | Maximum output voltage, RMS | > 4 V |
| S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL) | Typ. 76 dB(A) | Common mode rejection ratio (CMRR) | > 50 dB |
| Microphone length | 64 mm (2.5 in) | Equivalent noise level, ITU-R BS.468-4 | Typ. 25 dB |
| Output balance principle | Impedance balancing with Active Drive | Capsule diameter | 19 mm (0.75 in) |
| Frequency range, ±2 dB, at 60 cm (23.6 in) | 40 Hz - 20 kHz | Equivalent noise level, A-weighted | Typ. 18 dB(A) re. 20 µPa (max. 20 dB(A)) |
| Cable drive capability | 100 m (328 ft) | Microphone diameter | 19 mm (0.75 in) |
| Phase deviation for kit | < 10° | Sensitivity, nominal, ±2 dB at 1 kHz | 10 mV/Pa; -40 dB re. 1 V/Pa |
| Minimum load impedance | 2 kΩ | Weight | 58 g (2 oz) |
| Matching tolerance (frequency response and sensitivity) | ±1 dB | Frequency range | 20 Hz - 20 kHz |
| Output impedance | 100 Ω | Color | Matte black |
| Relative humidity (RH) | Up to 90% | Cartridge type | Pre-polarized condenser |
| Max. SPL, peak before clipping | 152 dB | Connector | XLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: - phase |
| Temperature range | -40°C to 45°C (-40°F to 113°F) |
